سنسور تنظیم ارتفاع خودکار محور Z مناسب دستگاهای CNC
- کد محصول: Z-Axis CNC
- موجودی: 5
- بازدید: 11764
- قیمت : 225,000 تومان
سنسور تنظیم ارتفاع خودکار محور Z مناسب دستگاهای CNC به کاربر این امکان را می دهد محور صفر Z را روی یک عمق دقیق تنظیم کند
Z-Probe یک جز جداشدنی است که یافتن موقعیت صفر محور Z شما را هنگام تنظیم
حکاکی ساده می کند پروب CNC سیستم کاوشگر یک ابزار اندازه گیری پیکربندی
شده بر روی ماشین های CNC برای اندازه گیری است ویژگیهای قطعات ماشین کاری شده
CNC ،تصحیح سیستم مختصات ،تشخیص خطا و غیره .
Material: wire+metal
Specification
Size: approx. 3.5 x 2cm
Effective surface of the knife: approx. 25mm
Line length: approx. 110cm
CNC Router Mill Tool Setting Touch Plate
CNC Z Axis Router Mill Touch Plate Tool Setting Probe New Milling Hot Kit
CNC Z Axis Router Mill Zero Check Touch Plate Mach3 Tool Setting Probe
These
touch plates make setting your tool height and zeroing your z-axis a
breeze. These are fully functional in and many other CNC controller
software.
Two ways to connect this item:
If your interface board has the limit switch port or other probe port, you can connect it to that port
If
your interface board does not have that port, your driver board has
that port, you can connect it to the driver board's limit switch port
Then
in the , you need to setup the probe( Config---Ports and Pins---Input
signals Probe enabled , the pin number type the one you use) and the
Auto-Tool-Zero. in the attachment, it is the code, you can edit it as
your requirements
Usage:
The wire connect on the control panel interface.
The clip and the control board GND (negative) is connected.
The tool can be clamped portion of the operation when the knife with a clip.
When the tool contacts the knife that the process is complete.
Note:
Manual measuring, please allow 0-1cm error!!!
مشخصات :
قطر خارجی: 40 میلی متر
ارتفاع : 20 میلی متر
طول کابل : 1 متر (100 سانتی متر )
دو روش برای اتصال این مورد:
اگر برد رابط شما دارای پورت سوئیچ لیمیت یا پورت پروب دیگری است، می توانید آن را به آن پورت متصل کنید
اگر برد رابط شما آن پورت را ندارد، برد درایور شما آن پورت را دارد، میتوانید آن را به پورت سوئیچ محدود برد راننده وصل کنید.
سپس در، باید کاوشگر (پیکربندی---پورت ها و پین ها---سیگنال های ورودی Probe فعال است، شماره پینی که استفاده می کنید) و Auto-Tool-Zero را تنظیم کنید. در پیوست، این کد است، شما می توانید آن را به عنوان نیاز خود ویرایش کنید
محصولات مرتبط
برچسب ها: سنسور, سنسور سی ان سی, سنسور تنظیم سطح خودکار محور Z, سنسور تنظیم سطح خودکار محور Z برای سی ان سی CNC