برد کنترلر   BIGTREETECH V1.4 Turbo یک مادر برد چاپگر سه بعدی  32 بیتی است که توسط تیم چاپ سه بعدی Shenzhen BigTree Technology CO  بهینه سازی و ارتقا یافته است

مشخصات  مادر برد کنترلر BIGTREETECH V1.4 Turbo  :

مدل: SKR V1.4 - 32bit

ولتاژ ورودی: DC12V- DC 24V/5A &15A

جنس: BCB چهار لایه

رابط درایور موتور: X , Y , Z , E0 , E1

ریز پردازنده: ARM cotrex-M3 CPU

پشتیبانی از درایورموتور -TMC2208 - TMC2130 - TMC210-ST820 - DRV8825 - LV8729 - A4988

رابط سنسور دما:‌ TH0 , TH1 , TB ,100K NTC

Gcodeهای گرفته  شده از نرم افزار های:  

Cura,Simply 3D,Pronterface,Reptier-host,Makerware

ویژگیهای مادر برد کنترلر BIGTREETECH V1.4 Turbo :

برد کنترلر BIGTREETECH V1.4 Turbo   با 32 بیت فرکانس اصلی 120 مگا هرتز سطح ARMCortex -M3 سری LPC 1769 با استفاده از آی سی اختصاصی برای عملکرد پیشرفته

مجهز به سیستم عامل بسیار مدولار و منبع باز 2.0 MarLin  که برای کاربران برای توسعه DIY و ثانویه مناسب است

با استفاده از توان آی سی اختصاصی M6130 از ورودی برق 12-24 ولت پشتیبانی می کند

لوله ماسفت MOSFET با عملکرد بالا ، برای جلوگیری از اتلاف بیشتر انرژی

 قابلیت از سرگیری چاپ درصورت خاموش شدن، قابلیت تشخیص شکستگی فیلامنت و خاموش شدن خودکار پس از اتمام چاپ

و....

استفاده از فیوز قابل جابه جایی برای تعویض آسان

  محتویات:

1.برد کنترلر

2.کابل USB

3.SD card

4. jumper cap

BIGTREETECH SKR V1.4&SKR V1.4 Turbo motherboard is a 32-bit 3D printer motherboard optimized and upgraded by the 3D printing team of Shenzhen BigTree Technology CO., LTD. for the deficiencies of V1.3 version, especially for small and medium-sized printers.
BTT SKR V1.4 & SKR V1.4 Turbo Features

1. BTT SKR V1.4 with 32-bit main frequency 100MHz ARM level Cortex-M3 series LPC1768 main control chip, the performance has been greatly improved.

2. BTT SKR V1.4 Turbo with 32-bit main frequency 120MHz ARM level Cortex-M3 series LPC1769 main control chip, the performance has been greatly improved.

3. Equipped with highly modular and open source firmware Marlin2.0, which is convenient for users to DIY and secondary development.

4. Using dedicated power chip M6130, support 12-24V power input.

5. Support 2.4, 2.8, 3.5 inch color touch screen, support LCD2004 screen, LCD12864 screen.

6. Upgrade and configure the firmware through SD card, which is simple, convenient and efficient.

7. The SPI and UART working mode driven by the TMC driver, also having the DIAG pin, which eliminates complex wiring process and can be used by simple unplugging jumper cap.

8. Support Resume Printing While Power Off, Filament Break Detection, Automatic Shutdown After Printing and so on.

9. High performance MOSFET tube, better heat dissipation effect.

10. Using removable fuse makes the replacement process easier.

11. Reserved extended port SERVOS and Probe to support BL Touch.

12. Support RGB light bar.

13. Use the power selection design to separate the USB power supply from the switch power supply, effectively avoiding the situation that the USB port of the computer is burnt out due to short circuit.

14. The special function interface uses the row needle with conspicuous color,which greatly reduces the error rate of wiring.

15. I2C, SPI and WIFI interfaces are reserved for convenience of DIY.

16. Closed-loop drive interface is reserved to reduce the trouble of plug-in switching module.

17. Double z-axis interface, eliminating the trouble of external drive expansion module.

18. The thermistor interface is protected by a bile capacitor pressurized resistor to enhance the resistance of the interface.

19. More fan interfaces: 1 way CNC fan, 3 way normally open fan.

20. Plug-in external DC5V power supply module to supply power to TFT screen, BLtouch and RGB.

Appearance size:110*85mm

Mounting size:102*76mm

Microprocessor:ARM Cortex-M3 CPU

Input voltage:DC12V-DC24V 5A-15A

Logic voltage:DC 3.3V

WIFI moduleESP-01S

Motor driver:Support TMC5161、TMC5160、TMC2209、TMC2225、TMC2208、

TMC2130、ST820、LV8729、DRV8825、A4988 etc., independent external motor

drive.

Driver working mode support:SPI、UART、STEP/DIR

Motor driver interface:X. Y. Z. E0. E1. 5 way(Each has a closed loop drive

interface) up to 256 subdivisions

Temperature sensor interface:TH0,.TH1, TB, 3 channel 100K NTC Temperature

sensor interface:TH0, TH1, TB, 3 channel 100K NTC (thermal resistance)

Display:2.4. 2.8. 3.5 inch TFT（Support dual mode screen）、LCD2004、

LCD12864

PC communication interface:Square USB, easy to plug, communication baud

rate of 115200

Expand the interface function support:Resume Printing While Power Off,

Filament Break Detection, Automatic Shutdown After Printing, Automatic leveling, BL Touch

Support file format:G-code

Supported machine architecture:XYZ. delta. kossel. Ultimaker. corexy

Recommended software:Cura、Simplify3D. pronterface. Repetier-host.

Makerware